loading
Model: IT-6000B
Shell material: UF Color: white (other colors can be customized)
Convenience cover: PE Control method: manual button + induction
Power supply voltage: input voltage AC100-240V 50/60Hz output 24V
Power consumption: Static ≤1.5W Dynamic ≤15W
Installation method: The installation board is separated from the host, and the installation is adaptive.
1. Induction/button control for changing sleeves
2. Humanized thermostatic seat ring
3. Urea-formaldehyde slow falling cover
4. The overall flip-up hatch
5. Delayed response
6. Motor overload protection
7. Multiple waterproof and moisture-proof
8. The maximum capacity of the cabin is 60 times
What to look for when choosing a toilet?
1. Determine the height of the drain according to the condition of the toilet and cut off the rest. The goal is to make the pipe and the bottom of the toilet more consistent. First use the hacksaw or cornea of the sewer according to the level of 0.5 cm, because the flange of the toilet is soft. If it is not 0.5 cm high, there may be water seepage problems, and the 0.5 cm fit is stricter.
2. Measure the pit distance. Before choosing a toilet, first determine the size of the water in the house, that is, the distance from the wall to the water. When using a toilet, if you are decorating tiles, you must measure the pit distance after applying the tiles. Otherwise, the toilet will not be able to be installed.
3. Install the flange ring provided with the toilet at the drain. Remember to press hard to ensure the tightness of the flange ring and toilet drain. Place the flange on the toilet drain. Then carefully align the lower hose and lower it smoothly. At this point, the wall of the downpipe will be inserted into the viscous clay of the flange to seal.
4. Once the test water is complete, start installing the cover.
5. Glue around the toilet, this step is also very important, not only to stabilize the toilet, but also to prevent the smell of the net from being released from the toilet. So we're not just fighting, we're fighting for four full weeks. At the intersection of the toilet bowl and the outer surface of the floor, since the toilet bowl and the floor are not integral, a joint sealing transparent sealant can be used to agitate and seal the outer opening of the toilet bowl to maintain the integrity of the floor. Some bathroom water can clog around the toilet. Note: If you need to install the set screw, first use the special sealant installed in the toilet, evenly apply it to the outer 2CM of the toilet base. The toilet drain should be oriented towards the center of the drain and pulled well. Where the expansion bolts are on the left and right side of the toilet, remove the toilet, punch and raised bolts.
6. Install or debug tank accessories.
7. After installing the toilet, wait until the glass glue (putty) or cement mortar has cured before draining the water. The curing time is usually 24 hours.
Model: IT-6000B
Shell material: UF Color: white (other colors can be customized)
Convenience cover: PE Control method: manual button + induction
Power supply voltage: input voltage AC100-240V 50/60Hz output 24V
Power consumption: Static ≤1.5W Dynamic ≤15W
Installation method: The installation board is separated from the host, and the installation is adaptive.
1. Induction/button control for changing sleeves
2. Humanized thermostatic seat ring
3. Urea-formaldehyde slow falling cover
4. The overall flip-up hatch
5. Delayed response
6. Motor overload protection
7. Multiple waterproof and moisture-proof
8. The maximum capacity of the cabin is 60 times
What to look for when choosing a toilet?
1. Determine the height of the drain according to the condition of the toilet and cut off the rest. The goal is to make the pipe and the bottom of the toilet more consistent. First use the hacksaw or cornea of the sewer according to the level of 0.5 cm, because the flange of the toilet is soft. If it is not 0.5 cm high, there may be water seepage problems, and the 0.5 cm fit is stricter.
2. Measure the pit distance. Before choosing a toilet, first determine the size of the water in the house, that is, the distance from the wall to the water. When using a toilet, if you are decorating tiles, you must measure the pit distance after applying the tiles. Otherwise, the toilet will not be able to be installed.
3. Install the flange ring provided with the toilet at the drain. Remember to press hard to ensure the tightness of the flange ring and toilet drain. Place the flange on the toilet drain. Then carefully align the lower hose and lower it smoothly. At this point, the wall of the downpipe will be inserted into the viscous clay of the flange to seal.
4. Once the test water is complete, start installing the cover.
5. Glue around the toilet, this step is also very important, not only to stabilize the toilet, but also to prevent the smell of the net from being released from the toilet. So we're not just fighting, we're fighting for four full weeks. At the intersection of the toilet bowl and the outer surface of the floor, since the toilet bowl and the floor are not integral, a joint sealing transparent sealant can be used to agitate and seal the outer opening of the toilet bowl to maintain the integrity of the floor. Some bathroom water can clog around the toilet. Note: If you need to install the set screw, first use the special sealant installed in the toilet, evenly apply it to the outer 2CM of the toilet base. The toilet drain should be oriented towards the center of the drain and pulled well. Where the expansion bolts are on the left and right side of the toilet, remove the toilet, punch and raised bolts.
6. Install or debug tank accessories.
7. After installing the toilet, wait until the glass glue (putty) or cement mortar has cured before draining the water. The curing time is usually 24 hours.